3. BATTERY REPLACEMENT
Flashing display indicates a low battery.
Slide off the battery cover in the direction
shown by the arrow and replace the
battery (positive side facing out).
battery
1. PREPARATION
1. Slide beam can be removed only after the locking
screw (A) is loosened.
2. Wipe clean all the measuring faces and slide
beam surface. No organic solutions must be used.
3. Check to see if all the buttons and the LCD display
are fully functioning.
2. OPERATION
1. With the gauge switched on, place measuring
face on a flat hard surface and press the depth
bar downward.
2.
Set the display to zero by pressing the “zero” button.
3. Select the measuring readout required by pressing
mm/inch button.
4. The gauge is now ready to take a reading.
NOTE: A flashing display will indicate a low battery
which should be replaced as soon as possible.
MAINTENANCE
1. Keep the gauge clean and dry (liquid can damage
the gauge).
2. Faces should be cleaned gently with cotton fabrics.
Never use petrol, acetone or other organic solutions.
3. In order to save power, turn off the unit when not in
use for a period of time.
DISPOSAL
At the end of the machine’s working life, or when it can
no longer be repaired, ensure that it is disposed of
according to national regulations.
Contact your local authority for details of collection
schemes in your area.
In all circumstances:
• Do not dispose of power tools with
domestic waste.
• Do not incinerate.
• Do not abandon in the environment.
• Do not dispose of WEEE* as
unsorted municipal waste.
25.00
MM
25mm
Fig 2
Fig 3
00.00
MM
PRESS
Fig 1
(A)
* Waste Electrical &
Electronic Equipment.
39591
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
INTRODUCTION
SCOPE
This tyre tread depth gauge is designed solely for the measurement of tread depth on a
vehicle tyre. Any use other than that it was designed for is considered misuse.
SPECIFICATION
Stock No.......................................................................................................................39591
Part No. ...........................................................................................................................TG2
Measuring range ............................................................................................... 0-25mm/0-1"
Resolution ....................................................................................................0.01mm/0.0005"
Accuracy.......................................................................................................≤0.05mm/0.002"
Measuring system .........................................................Linear capacitive measuring system
Display.................................................................................................................LCD display
Power ..........................................................................................................1.5V SR44/LR44
Working temperature............................................................................................5°C – 40°C
HANDLING AND STORAGE
Do not drop the tyre gauge as it can damage and shorten the lifespan of the unit.
Store in a dry location.
TECHNICAL DESCRIPTION
CONTACTS
OPERATION
IDENTIFICATION
(1)
Slide beam
(2)
Measuring face
(3)
Power ON/OFF switch
(4)
Display (LCD)
(5)
mm / inch conversion switch
(6)
Slider clamp screw
(7)
ZERO switch
(8)
Battery compartment lid
(2)
(3)
(4)
(5)
(7)
(6)
(8)
(1)
25.00
MM
Helpline: (023) 8049 4344
Sales Desk: (023) 8049 4333
Internet: drapertools.com
E-mail: [email protected]
General Enquiries: (023) 8026 6355
Draper Tools Limited, Hursley Road, Chandler's Ford, Eastleigh, Hampshire. SO53 1YF. U.K.
Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your
local area.
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
DBTL0519
DIGITAL TYRE TREAD
DEPTH GAUGE
