Dräger Polytron 7500 Instructions For Use Manual Download Page 63

Page: 63 / 72

9023927 - 2nd edition - May 2007

Technical Data

Technical Data

The measuring range and the measuring properties depend on the DrägerSensor –
see the Instructions for Use of the DrägerSensor being used.

Type

Microprocessor controlled transmitter with pump and pyrolysis oven

Measuring range and the measuring
properties

depend on the type –
see the Instructions for Use of the installed DrägerSensor

Flow rate

900 ±100 mL/min;
Hose inside diameter 4 mm, hose outside diameter 6 mm

Signal transmission to the central unit
Analogue:

Measured-value signal

4 mA to 20 mA

Drift below zero point

3.8 mA

Measuring range exceeded

20 mA to 20.5 mA

Unit fault

<3.2 mA; 21 mA

Maintenance signal

3.4 mA ±0.2 mA constant

Digital:

HART compatible, transmission on 2-wire shielded cable
optionally LON

Supply voltage

24 V DC ±2 V; 1.5 A

Cable inlet

M20x1.5, for cable diameter 6 to 12 mm (0.24" to 0.47")

Ambient conditions

Speciﬁcations for the sensor: see the Instructions for Use for the DrägerSensor
0 to 40

700 to 1300 hPa
0 to 99 % relative humidity, no condensation

Dimensions (H x W x D)

150 mm x 125 mm x 300 mm

Weight

approx. 2.4 kg

CE markings

Electromagnetic compatibility (Directive 89/336/EEC)

Ingress protection

IP 21

Relay module:

logical channels

A1, A2, Fault

principle

normally energised (for fail-safe operation)

contacts

1-pole changeover (SPDT)

contact rating

5 A at 30 V DC; 5 A at 250 V AC

Summary of Contents for Polytron 7500









































































Search results

Summary of Contents for Polytron 7500

Reviews:

Related manuals for Polytron 7500

Brands by name

Popular brands

Dräger Polytron 7500, Instructions For Use Manual

Search results

Summary of Contents for Polytron 7500

Reviews:

Related manuals for Polytron 7500

Brands by name

Popular brands