manualshive.com logo in svg

Dräger Isolette 8000 plus, Instructions For Use Manual, Page: 4 / 30

Share
Download
Dräger Isolette 8000 plus Instructions For Use Manual Download Page 4

4 

 Supplement to the instructions for use

  |  

Isolette 8000 plus

  

Information about this document

1 

Information about this document

Keep this supplement with the instructions for use.

This supplement updates the information given in the instructions for use in the 
following chapters: Information about this document, For your safety and that of 
your patients, and Reprocessing

1.1 Trademarks

1.1.1 

Trademarks owned by Dräger

The following web page provides a list of the countries in which the trademarks are 
registered: www.draeger.com/trademarks

1.1.2 

Trademarks owned by third-party manufacturers

Instructions for use

Part number

Edition

Isolette 8000 plus

MU25944

4 –  and higher

Trademark

 Dräger

®

 Isolette

®

 Softbed

®

Trademark

Trademark owner

Dismozon

BODE Chemie

Neodisher  mediclean

Dr. Weigert

acryl-des

Schülke & Mayr

Buraton
Mikrozid
Perform
terralin protect
Virkon

DuPont

Actichlor

Ecolab USA

Oxycide
BruTab 6S

Brulin

Clorox Professional

Clorox

Dispatch
Klorsept

Medentech

Descogen

Antiseptica

Summary of Contents for Isolette 8000 plus































Reviews:

No comments