Dräger Fabius 4116029 Technical & Service Manual Download Page 86

Page: 86 / 328

Fabius

Repair Instructions

3-18

Cop

ight

2000 Dr

aeger

edical,

sec3_

repa

instr

uc_c.

Error Log

Error

Error Description

Possible Cause

No error

Reset; cause unknown

Hardware error. Electromagnetic
interference. EEPROM needs
replaced

RAM (Control PCB)

RAM needs replaced.

EPROM (Control PCB)

EPROM needs replaced.

Watchdog reset (Control PCB)

Hardware error. Software error.
Watchdog time exceeded.

A/D converter

Error during A/D conversion.

Graphics display

Graphics display or connector
needs replaced.

Battery

Wrong battery installed or
installed battery flat.

Analog voltage

Error in ±12 V voltage supply.
Control PCB needs replaced.

Supply voltage

Battery exhausted during power
supply from battery.

EEPROM*

Read/write error during system
start-up. EEPROM needs
replaced. Data error.

EEPROM* write error

Error during EEPROM writing.
EEPROM needs replaced. Data
error.

EEPROM* read error

Error during EEPROM reading.
EEPROM needs replaced. Data
error.

RAM backup error

Error while reading internal RAM
data during system start-up.

Data check error/system reset
occurs

Checksum of settings or
operating mode incorrect.

Communication error

RAM locations inverted or needs
replaced.

Calibration value check error (O

sensor, pressure sensor, flow
sensor, PEEP valve)

EEPROM error. RAM error.
Standard values are being used.

Calibration required.

* Later models do not have an EEPROM and require board replacement.

Rev. A

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029








































































































































































































































































































































Search results

Summary of Contents for Fabius 4116029

Reviews:

Dräger Fabius 4116029, Technical & Service Manual, Page: 86 / 328

Search results

Summary of Contents for Fabius 4116029

Reviews: