Dräger Fabius 4116029 Technical & Service Manual Download Page 82

Page: 82 / 328

Fabius

Repair Instructions

3-14

Cop

ight

2000 Dr

aeger

edical,

sec3_

repa

instr

uc_c.

"Monitor" (MON) Display Field

Overview: MON

0000 ==> no errors
00XX ==> O

sensor error

0X00 ==> pressure sensor error
X000 ==> flow sensor error

1000

Communication error from
Control PCB to Power PCB.

Line interruption in ribbon cable,
bent connector.

2000

Communication error from Power
PCB to Control PCB.

Line interruption. Power PCB does
not work (see error 1000).

4000

Motor current temporarily too high.

Incremental encoder lost
increments. Contamination,
scratches, light barrier needs
replaced

8000

Motor current continuously too high. Power amplifier needs replaced.

Motor open.

Error

Error Description

Possible Cause

0001

FiO

sensor voltage too low.

sensor needs replaced.

sensor calibrated incorrectly.

0002

FiO

sensor voltage too high.

sensor needs replaced.

sensor calibrated incorrectly.

0004

FiO

measured values outside

permissible range.

sensor needs replaced

0008

FiO

time-out during calibration.

sensor needs replaced.

Sensor not yet stabilized.
Calibration of O

sensor at changing

concentration or O

concentration

not corresponding to calibration mode
(21%/100%).

0010

FiO

/relative error between FiO

sensor channels > 25%.

sensor needs replaced.

0020

FiO

calibration constant from

EEPROM incorrect.

sensor not yet calibrated.

Data loss in the EEPROM.

0040

FiO

/coding for calibration.

Current error occurred during
calibration.

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029








































































































































































































































































































































Search results

Summary of Contents for Fabius 4116029

Reviews:

Dräger Fabius 4116029, Technical & Service Manual, Page: 82 / 328

Search results

Summary of Contents for Fabius 4116029

Reviews: