manualshive.com logo in svg

Dräger Fabius 4116029, Technical & Service Manual, Page: 277 / 328

Share
Download
Dräger Fabius 4116029 Technical & Service Manual Download Page 277

Fabius

®

Spare and Replacement Parts

Cop

yr

ight

 2000 Dr

aeger

 M

edical,

 In

c.

sec5_p

ar

ts_

c.fm 

ITEM                          DESCRIPTION

PART NUMBER

Flowmeter assemblies. . . . . . . . . . . . . . . . . . . . . . . . . .2603012 (illustrated), 2603504, 2600332, 2605010
1.

ORC mounting plate  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4116069

2.

Hanger (1x per tube) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2600303

3.

Upper rear tubing plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2600316

4.

Tube (2x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2600317

5.

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2600318

6.

Upper flowmeter block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M33601

7.

Glueing foil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2600320

8.

O-ring (4x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M16201

9.

Spring (1x per tube). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M12928

10. O-ring (2x per tube) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M34329
11. Fitting, pilot to Divan (3x). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M28816
12. Flow tube, O2, 0.02 - 0.50 L/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115648
13. Flow tube, O2, 0.55 - 10 L/min  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115649
14. Flow tube, N2O, 0.02 - 0.5 L/min. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115650
15. Flow tube, N2O, 0.55 - 10 L/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115651
16. Flow tube, Air. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115647
17. Washer, DIN 7168 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30297
18. Fitting, 90° elbow G 1/8(2x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30935
19. Washer, 4 mm blue (6x). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30937
20. Ferrule, pilot to Divan (2x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30963
21. Fitting, straight, M5 (7x). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30952
22. Fitting, 90° elbow (2x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30953
23. Fitting, Luer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30960
24. Washer, M4, white (8x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M31602
25. Collar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M31603
26. Bottom flowmeter block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M32641
27. Pressure gauge (3x)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M33402
28. DW Ball (plug) (12x)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1270656
29. Screw, M3 x 4 DIN 927 - A2/051 (4x)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1329383
30. Screw, M4 x 10 DIN 912 - A4/051 (2x)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1320858
31. Screw, M4 x 12 DIN 912 - A2 (2x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1293664
32. Nut, hex, M5 DIN 980 - A4/051 (4x)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1335618
33. Washer, spring, M4 DIN 127 (4x)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1331345
34. DI screw (4x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1331930
35. Proportional valve (ORC)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M32940
36. Knob, A1 (2x). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2600304
37. Knob. ISO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2600309
38. Safety valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115950
39. Flow control valve (3x). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115871
40. Valve, pillar (3x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4115951
41. Y-plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M30962
42. Screw, M5 x 10 DIN 7991 - 8.8/155 (4x) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1336134

Hose, 2.7 x 0.65 PAE - blue (820 mm total)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210211
Hose, 2.7 x 0.65 PAE - bl/white (500 mm total). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210181
Hose, 2.7 x 0.65 PAE - white (610 mm total). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210157
DW hose, 4mm x 1mm PAE NF clear (550 mm total) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210173

Rev. A

5-11

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029









































































































































































































































































































































Reviews:

No comments