background image

 

Quintaflex R96 

Ceiling, Wall Model

 

Dr. Mach

 

Lamps and Engineering

 

 

59250001 

Edition 01 

21.02.2002 / Bak  Page 5/18

 

 

2. Operating the lamp Quintaflex R96 

 

2.1 Checking the lamp Quintaflex R96 with light intensity control 

 
The lamp Quintaflex is optionally equipped with the function of electronic light intensity control. You can 
adjust the light intensity at the key pad on the cardan bow. 
 

♦ 

Voltage measurement and setting 

 
Before using the OT-lamps, a voltage measurement and, if necessary, a voltage setting has to be done. 
Only in this way a perfect functioning can be ensured. 
If the location of the lamp is changed, the voltage measurement and setting must be repeated. 
 

♦ 

Voltage measurement at the halogen bulbs 

 

 

 

To measure the voltage proceed as follows: 
Mount the lamp to the ceiling or wall attachment. 
Switch on the lamp. 
In order to make the measurement, remove the 
cover. 
The cover is fixed with two screws, as shown in the 
figure. Loosen the two screws, remove them and 
take off the cover. 
 

 

The measuring points for checking the voltage are in 
the same position at all Quintaflex-lamps. 
The measuring points are shown in the figure. 
 
At measuring points 

1 + 2

 measure the voltage 

applied at the halogen bulbs. 

The lamp is set to the 

maximum light intensity

 
The AC or DC voltage depends on the external power 
supply. 
Rated voltage 22,8 – 23,8V. 

 

♦ 

Voltage setting at the halogen bulbs 

 

 

 

If the voltage measured is too high or too low, the 
value must be adjusted at the power supply. 
The setting at the transformer is made by 
reconnecting the wires on the secondary side. 

Measuring points 
1+2 

Measuring points 

Measuring points 

Screw 

Screw 

Summary of Contents for 5502 3031 27






















Reviews: