manualshive.com logo in svg

Dover markem imaje CSAT ITS6 210, Operating Instructions Manual

Share
Download
Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 331

 

Operating Instructions 

Maintenance and Repair 

 

 

© Copyright by Markem-Imaje CSAT GmbH 

 

ITS6_135_Manual_EN.doc 

Subject to Technical Modifications 

Page 331 / 370 

 

10.7.7  Checking and cleaning the pre-curing unit 

The  lamp  modules  of  the  precuring  unit  located  beneath  each  print  head 
always have to be kept clean. If they become too dirty, not enough light can 
be transmitted to the applied ink. As a result, the ink might not be properly 
crosslinked and the different colors could run into each other. 

Required aids: 

 

Clean, solvent-resistant protective gloves (see Chap. 2.5.5) 

 

Spotless cleaning cloth for print heads CSAT order no.: 

FF100252100

 

 

Cleaning fluid suitable for the type of UV ink used 

 

Notice 

The print heads located next to the lamp modules of the pre-curing 
unit are very sensitive! Therefore… 

  never touch their nozzle plates with your bare fingers 

  do not exert pressure on the nozzle plates 

  do not work with hard objects in the area beneath the print heads 

  therefore, remove bracelets and rings. 

Non-compliance will result in the loss of all warranty rights! 

 

The  lamp  modules  of  the  pre-curing  unit  are  not  cleaned  during  the  me-
chanical print head cleaning process, but rather, they can 

– and must – be 

cleaned by hand only. This is usually done at the same time as the manual 
cleaning of the print heads, but it can also be done more often as needed 
according to the following instructions. 

In order to be able to check and clean the lamp modules of the pre-curing 
unit, the entire print head unit has to be pushed back into its service posi-
tion. 

> 

Stop the printing process. 

> 

Wait until the printer has shut 
down completely. 

 

 

> 

Open the middle door at the 
rear of the printer. 

 

 

 

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands