Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 310 | Manualshive

Page: 310 / 370

background image

Maintenance and Repair

Operating Instructions

© Copyright by Markem-Imaje CSAT GmbH

Page 310 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

10.6.10 Replacing the lighting unit on the camera system

Information

When you replace the lighting unit on the camera system, pay particular
attention to the deflecting mirror and the camera. Avoid any damage to
deflecting mirror and camera lens, and any change of the camera ad-
justment.

Replacing the lighting unit

Use the following procedure to replace the lighting unit:

>

Stop the printing process.

>

Wait until the printing system has
stopped.

>

Shut down the printing system via
the touchscreen.

>

Press the red button of the
ON/OFF switch.

>

Disconnect the printing system
from the power supply system. To
do this, set the main switch to
"0/OFF".

>

Open the hinged hood.

>

Loosen the two knurled screws #1
on the mirror carrier #2, and re-
move the knurled screws and the
mirror carrier.

>

Disconnect the plug-in connec-
tion #3 of the lighting.

1

2

3

«
...
308
309
310
311
312
...
»

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Reviews:

No comments

Related manuals for markem imaje CSAT ITS6 210

Power Defense PD3

Brand: Eaton Pages: 4

Brand: Olympus Pages: 2

Brand: Olympus Pages: 148

Brand: TallyGenicom Pages: 92

Brand: Keeler Pages: 25

Brand: Samsung Pages: 115

Brand: Star Pages: 88

Brand: Creality Pages: 24

Brand: Ricoh Pages: 955

Oce VarioPrint i Series

Brand: Canon Pages: 29

Brand: Canon Pages: 138

Oce Arizona 1200 Series

Brand: Canon Pages: 226

Brand: Canon Pages: 36

imageCLASS LBP247dw

Brand: Canon Pages: 32

Expression Home XP-305

Brand: Epson Pages: 45

Brand: Epson Pages: 32

Expression Home XP-245

Brand: Epson Pages: 4

Expression Home XP-212

Brand: Epson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands