Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 173 | Manualshive

Page: 173 / 370

background image

Operating Instructions

Machine Description

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 173 / 370

4.11

Menu System

The menu System is where general system settings are made, for instance
the network configuration or the system time. As a rule, these settings are
not job-specific and, therefore, rarely have to be changed.

4.11.1 Tab System > Settings

This tab is used to change the touchscreen display language, the system
time, and the passwords of the logged-in users.

Fig. 67. Tab System > Settings

Pos. Item

Meaning

1

Language

Selection of the desired display language. After hitting the
desired key, the display language of the MHI will change with-
in a few seconds.
Only one language can be selected at a time.

2

System
date and
time

Setting of the current time for the touchscreen and printer.
After hitting the “command prompt” key, an input box will ap-
pear in which the new system time setting can be entered.

3

Password
current
user

Changing your own password.
After hitting the “command prompt” key, a logged-in user can
replace his previous password with a new one. The pass-
words of other users cannot be changed here.
Each password must be at least six characters long and con-
tain numbers as well as at least one upper case and lower
case letter each. The characters can be put in any desired
order.

1

2

3

«
...
171
172
173
174
175
...
»

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Reviews:

No comments

Related manuals for markem imaje CSAT ITS6 210

Brand: Xerox Pages: 341

PIXMA MG5600 Series

Brand: Canon Pages: 4

Brand: Ricoh Pages: 278

Brand: Oki Pages: 57

Brand: Oki Pages: 204

Brand: Oki Pages: 336

Brand: Oki Pages: 137

8200DX - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 2

Brand: Oki Pages: 182

Brand: Konica Minolta Pages: 285

DocuPrint 96 IPS Series

Brand: Xerox Pages: 101

Robojet Disc Autoprinter

Brand: Aleratec Pages: 38

Brand: Roland Pages: 116

Brand: Xerox Pages: 2

Brand: Brother Pages: 9

PocketJet 3 Plus

Brand: Brother Pages: 11

Brand: Brother Pages: 2

Brand: Brother Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands