Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 91 | Manualshive

Page: 91 / 136

background image

Issued May 2020

Maintenance and Adjustment

Copyright 2020, Heil Environmental
Printed in the U.S.A.

Maintenance and Adjustment

85

DRAIN AND CLEAN THE HYDRAULIC OIL TANK (CONTINUED)

NOTICE

Before filling the tank be sure the funnel is clean and 200 mesh (or finer) screen is used to strain the hydraulic oil.

13.Fill tank with recommended oil, checking the sight gauge as you fill. Refer to

Hydraulic Oil Specifications

.

14.Check the entire system to make sure all connections are tight and no leaks are found.

15.Start the truck’s engine and engage the pump.

WARNING

Moving equipment can be dangerous to bystanders. Serious injury or death can occur if a person is in the wrong area or is
not attentive to the operations. Clear the area of all unnecessary people before you operate the controls.

16.Operate the packing panel through 10 cycles to be sure all air is out of the circuits.

17.Operate the automated container lift mechanism.

18.Operate tailgate – full up and full down.

19.Operate body raise (dump units) – full up and full down.

20.With the packing panel in the retracted position and lift in the in-transit position, check tank oil level. If necessary, add

recommended as described under

Check Oil Level

.

PURGE THE HYDRAULIC SYSTEM

If the hydraulic system becomes contaminated because of component failure or some other reason, you must purge the
hydraulic system.

To purge the system, follow these steps:

1. Extend the packer/ejector cylinder to lower the oil level in the tank.

2. Remove and replace the in-tank oil filter element in the tank.

3. Engage the packer/ejector control lever and allow the oil to circulate through the new filter, cleaning the oil.

NOTICE

Before filling the tank be sure the funnel is clean and 200 mesh (or finer) screen is used to strain the hydraulic oil.

4. Repeat the procedure as necessary until the system is purged.

NOTICE

If contaminated hydraulic oil reaches the cylinders, the unit may need to be removed from service until the contamination
is removed. For more information, contact the Heil Technical Services.

16

83

«
...
89
90
91
92
93
...
»

Summary of Contents for HEIL LIBERTY TP1L-SM-0520









































































































































Reviews:

No comments

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brand: Walker Bay Pages: 8

Brand: Quark-Elec Pages: 2

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 24

Brand: GAPOSA Pages: 32

INTRAmatic 31 ES

Brand: KaVo Pages: 52

Brand: Raytec Pages: 8

Brand: StarDental Pages: 2

Brand: USC Pages: 29

LED Niova 150-F Pro 150W Bi Color

Brand: Walimex Pro Pages: 56

Brand: Sport-thieme Pages: 20

Brand: Ivoclar Vivadent Pages: 64

Brand: Tascam Pages: 44

Brand: NordicTrack Pages: 16

Redstone OSA305

Brand: THORLABS Pages: 52

SourceMeter 2425

Brand: Keithley Pages: 141

Brand: Lithium Grim Pages: 13

Trillium Compact

Brand: Nanometrics Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands