Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 88

Page: 88 / 136

Issued May 2020
Maintenance and Adjustment

Printed in the U.S.A.

Maintenance and Adjustment

PREPARING THE UNIT TO CHECK THE OIL LEVEL

Before checking the oil level or adding oil, make sure the unit is in the following position with all cylinders collapsed:

Truck – on level ground

Tailgate and Body – fully down and locked

Packer Panel – in the in-transit position with all cylinders retracted

Lift Arm (if equipped) – is fully retracted

The oil tank is mounted behind the chassis cab. The oil level in the standard tank must be kept between the low and full
marks as indicated on the sight gauge. See the figure below.

Figure 31. Hydraulic Oil Tank and Sight Gauge

Summary of Contents for HEIL LIBERTY TP1L-SM-0520










































































































Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands

Dover HEIL LIBERTY TP1L-SM-0520, Service Manual

Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands