Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 79 | Manualshive

Page: 79 / 136

background image

Issued May 2020

Body and Tailgate

Copyright 2020, Heil Environmental
Printed in the U.S.A.

Body and Tailgate

73

WELDING AND ELECTRONIC DEVICES / ELECTRICAL LUBRICANTS

proximity switches complete the following procedures.

WARNING

Never weld on a compressed natural gas vehicle unless the compressed natural gas fuel system has been purged with
inert gas. See Service Manual Section 1.

Disconnect all battery connections.

Place welding ground as close as possible to the area that is being repaired.

Disconnect the Cortex Controller and all other electronic control units (ECUs).

If welding within 24 inches of a proximity switch, remove the switch from the unit.

NOTICE

Failure to follow these procedures may cause damage to the devices. The damage comes from the inability of the devices
to withstand the amperage, open circuit voltage and magnetic flux a welder can produce.

Electrical Anti-Corrosion Lubricant

It is very important that all Packard connectors are properly lubricated. The following compounds, by brand name, or
functional equivalents, are approved for use.

Truck-Lite Corrosion Preventive Compound

GB ox-gard, anti-oxidant compound

Burndy Penetrox A electrical joint compound.

These lubricants may be obtained at an electrical supply store.

«
...
77
78
79
80
81
...
»

Summary of Contents for HEIL LIBERTY TP1L-SM-0520









































































































































Reviews:

No comments

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

Brand: FJC Pages: 2

Brand: Banfer Pages: 6

Brand: Gaspardo Pages: 196

Brand: RAB Pages: 2

Brand: Farmi Forest Corporation Pages: 32

Brand: ParaBody Pages: 3

Brand: Hach Pages: 52

Brand: hager Pages: 2

The Wave Transformer

Brand: EarthQuaker Devices Pages: 21

Brand: Rapala Pages: 14

Brand: S.R.Smith Pages: 43

Brand: M-Audio Pages: 3

Brand: ubicquia Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands