Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 78 | Manualshive

Page: 78 / 136

background image

Issued May 2020
Body and Tailgate

Copyright 2020, Heil Environmental

Printed in the U.S.A.

Body and Tailgate

72

TAILGATE UNLATCH LIMIT SWITCH (N.C.)

The Tailgate Unlatch Limit Switch (N.C.) is non-adjustable and mounted on the tailgate with the striker mounted on the
tailgate hinge. It is activated by breaking contact with the striker. When the tailgate latch is released, causing the striker to
move, this switch interrupts an electrical circuit causing an alarm to sound, warning the operator that the tailgate is not fully
closed and latched.

CAUTION

If the tailgate unlatch limit switch does not activate the alarm, DO NOT operate the truck. Further troubleshooting is
required.

PACKER REVERSING LIMIT SWITCH (N.C.)

The Packer Reversing Limit Switch (N.C.) is non-adjustable located under the body behind the packer actuator plate. This
switch is used to signal when to reverse the direction of the packer paddle in the automatic packing condition. It should be
mounted so that the reversing motion of the packer paddle occurs before the left or right hand packer cylinder completely
bottoms out. If this switch does not work, the body full alarm will sound.

«
...
76
77
78
79
80
...
»

Summary of Contents for HEIL LIBERTY TP1L-SM-0520









































































































































Reviews:

No comments

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: Hantek Pages: 124

Brand: Hameg Pages: 10

Brand: OHAUS Pages: 84

Brand: Parkside Pages: 95

Brand: Park House Healthcare Pages: 32

Brand: Feniex Pages: 5

Brand: Atlas Metal Pages: 2

Brand: ALL-FILL Pages: 32

ESK+ Manual Knee Lock

Brand: Blatchford Pages: 172

Brand: HEINE OPTOTECHNIK Pages: 52

Brand: Ugin Pages: 39

Brand: Tripp Lite Pages: 24

Brand: TDX Tech Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands