Dover HEIL LIBERTY TP1L-SM-0520 Service Manual Download Page 105

Page: 105 / 136

Issued May 2020

Body Controller Software

BODY CONTROLLER SOFTWARE

BODY CONTROLLER OUTPUTS

Figure 40. Body Controller Outputs

State of each output in brackets [ ].

All Outputs

[ON] - Output is On.

[OFF] - Output is Off.

Diagnostic features outputs 00 thru 07

[Disabled] - Output is disabled by option set or spare.

[Under Voltage on VBB] - Supply Voltage is too low.

[Over Voltage on VBB] - Supply Voltage is too high.

[Settings Invalid] - Program Error.

[Wire Break] - Open Circuits Detected

[Short Circuit] - Short Circuit Detected

[Over Current] - Overload on Circuit

Diagnostic features outputs 08 thru 15

[Disabled] - Output is disabled by option set or spare.

OUTPUT

PIN#

DESCRIPTION

OUT00

HOPPER COVER OPEN

OUT01

HOPPER COVER CLOSE

OUT02

BODY RAISE SOL

OUT03

BODY LOWER SOL

OUT04

TG RAISE SOL

OUT05

TG LOWER SOL

OUT06

DIVERTER SOL

OUT07

TG ALARM

OUT08

SPARE

OUT09

SPARE

OUT10

PACK LEFT SOL

OUT11

PACK RIGHT SOL

OUT12

SPARE

OUT13

LIFT RAISE ILOCK SOL

OUT14

LIFT RETRACT SOL

OUT15

LIFT RAISE SOL

Summary of Contents for HEIL LIBERTY TP1L-SM-0520










































































































Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands

Dover HEIL LIBERTY TP1L-SM-0520, Service Manual

Search results

Summary of Contents for HEIL LIBERTY TP1L-SM-0520

Reviews:

Related manuals for HEIL LIBERTY TP1L-SM-0520

Brands by name

Popular brands