manualshive.com logo in svg

Dot Hill Systems AssuredSAN 6004, Cli Reference Manual, Page: 142 / 363

Share
Download
Dot Hill Systems AssuredSAN 6004 Cli Reference Manual Download Page 142

142 Alphabetical list of commands

show degraded-disk-thresholds

Description

Shows the configured criteria for the system to identify degraded disks. If no parameter is specified, 

the command shows information for all degraded disks.

Min. role

monitor

Syntax

show degraded-disk-thresholds

[name 

threshold-name

]

Parameters

name 

threshold-name

Optional. Specifies one of the following values (which identifies the disk tier and RAID redundancy 

level) for which to show information:

•

archive-single

: Archive tier, single redundancy RAID.

•

archive-dual

: Archive tier, dual redundancy RAID.

•

archive

: Archive tier, any RAID level.

•

standard-single

: Standard tier, single redundancy RAID.

•

standard-dual

: Standard tier, dual redundancy RAID.

•

standard

: Standard tier, any RAID level.

•

performance-single

: Performance tier, single redundancy RAID.

•

performance-dual

: Performance tier, dual redundancy RAID.

•

performance

: Performance tier, any RAID level.

•

all-single

: All disks, single redundancy RAID.

•

all-dual

: All disks, dual redundancy RAID.

•

all

: All disks, any RAID level.

Disk tiers are defined as:

•

archive

: Disks with rotation speeds below 10K RPM. In this system, these are midline SAS 

disks.

•

standard

: Disks with rotation speeds greater than or equal to 10K RPM. In this system, these 

are enterprise SAS disks.

•

performance

: SAS SSDs.

•

all

: Disks are not differentiated by disk tier.

RAID redundancy levels are defined as:

•

single

: Disks used in a RAID type other than RAID 6.

•

dual

: Disks used in RAID 6.

Output

Name

The threshold name.

Target

•

Recoverable Errors

: Soft errors (sense key 1).

•

Unrecoverable Errors

: Medium errors (sense key 3).

ThresholdA, ThresholdB, ThresholdC

Configured criteria for how many errors of the target type must occur within a certain time period for 

a disk to be considered degraded. The format is 

period.duration.threshold-value

, where:

•

period

: Hour, day, or week.

•

duration

: A numeric value for the duration of the period.

•

threshold-value

: A numeric value for the threshold count.

•

--

: Threshold is not set.

Summary of Contents for AssuredSAN 6004












































































































































































































































































































































































Reviews:

No comments