manualshive.com logo in svg

Dot Hill Systems AssuredSAN 4544, Setup Manual

Share
Download
Dot Hill Systems AssuredSAN 4544 Setup Manual Download Page 85

AssuredSAN Ultra48 Series Setup Guide

85

Physical requirements

The floor space at the installation site must be strong enough to support the combined weight of the rack, 

controller enclosures, drive enclosures, and any additional equipment. The site also requires sufficient 

space for installation, operation, and servicing of the enclosures, together with sufficient ventilation to allow 

a free flow of air to all enclosures.

Figure 46

 and 

Table 32

 on page 86 show enclosure dimensions and weights. Enclosure designators are 

described below. Enclosure weights assume the following configuration characteristics:

•

2U48 enclosure (high-capacity with SFF disks)
• “2U48” denotes the 2.5" 48-drive enclosure (with controller or expansion modules)
• The 2U48 chassis includes three installed drawer slots that must be populated with disks and 

possibly AMS inserts if applicable, after the enclosure is installed into the rack. The table in this 

section assumes each drive slot contains a disk drive module.

•

2U24 enclosure (comparative enclosure dimensions are provided for reference):
• “2U24” denotes the 2.5" 24-drive enclosure (with controller or expansion modules)
• The 2U24 chassis is equipped with a disk in each disk drive slot

NOTE:

For 2U24 product information, see the 

AssuredSAN 4004 Series Setup Guide

.

•

2U12 enclosure (comparative enclosure dimensions are provided for reference):
• “2U12” denotes the 3.5" 12-drive enclosure (with controller or expansion modules)
• The 2U12 chassis is equipped with a disk in each disk drive slot

NOTE:

For 2U24 product information, see the 

AssuredSAN 4004 Series Setup Guide

.

•

Two controller modules or two expansion modules per enclosure

•

Two power supply modules per enclosure

NOTE:

The following table provides comparative measurements for the 2U48, 2U24, and 2U12 

enclosures supported by AssuredSAN 4004 Series.

This document describes the AssuredSAN Ultra48 Series controller enclosures. Measurements for the 2U24 

and 2U12 enclosures are included within the table portion of 

Figure 46

 on page 86 simply for ease of 

comparison. For information about the 2U24 and 2U12 enclosures, see the 

AssuredSAN 4004 Series 

Setup Guide

.

Summary of Contents for AssuredSAN 4544





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands