Dormakaba 630 Series Installation Instructions Manual Download Page 9

Page: 9 / 22

Exit Device Operators 630/750/79E/RT/E7900 Series/ Generation E-730 PK3677_T

10-18

CAUTION

WARNING

IMPORTANT

Perform the following procedures in order, with the

door OPEN unless otherwise indicated.

1 Panic Bar

Activate the panic bar. The latch bolt or rod

retracts fully.

2 Outside Lever

Turn the outside lever downward. The latch bolt or

rod does not retract.
If the latch bolt or rod retracts, verify that the bat-

teries are properly installed.
If the lever feels tight (hard to turn, or does not

return easily to its horizontal rest position), check

the spindle length vs. the door thickness (the spin-

dle may be too long). Check that the slotted end of

the spindle is inserted in the lock housing hub, not

the exit device.

3 Electronics and Card Reader

Test the lock’s response to keycards: a Test key-

card, a Grand Master keycard, and an Emergency

keycard.
Insert keycards as shown below, with the magnetic

stripe facing toward the door and to the left. For

79E, present cards to reader.

E Test the operation of the E-730/750/79E lock

(for 630 lock go to Section H) (For RT lock series, please refer to

system 6000 manual)

A Test the Lock Before Programming

Normal Entry: Use the Test keycard with the reader.

The red and green LEDs each flash once and then

the green LED flashes for four seconds.
Turn the outside lever downward while the green

LED is flashing. The latch or rod retracts fully.

Release the lever, then turn it again. The latch or rod

must not retract after the LED stops flashing with-

out first inserting the keycard.

B Lock Programming

Program the lock with its Common Area number

(exit devices are usually programmed as common

areas, see Reference Manual).
Use the Grand Master keycard with the reader. The

green LED flashes. Turn the outside lever down-

ward while the green LED is flashing. The latch or

rod retracts fully and the LED stops flashing after

4 seconds. Release the lever, then turn it again. The

latch or rod must not retract again without first

inserting the keycard.

C Emergency Keycard Access

Use the Emergency keycard with the reader. The

green LED flashes for 4 seconds. Then, turn the

outside lever downward. The latch or rod retracts

fully.

While standing outside the room, close the door and

ensure that it is properly latched. Open the door

using the Grand Master keycard using the same

procedure.

Summary of Contents for 630 Series























Search results

Summary of Contents for 630 Series

Reviews:

Related manuals for 630 Series

Brands by name

Popular brands

Dormakaba 630 Series, Installation Instructions Manual

Search results

Summary of Contents for 630 Series

Reviews:

Related manuals for 630 Series

Brands by name

Popular brands