Dormakaba 630 Series Installation Instructions Manual Download Page 20

Page: 20 / 22

Exit Device Operators 630/750/79E/RT/E7900 Series/ Generation E-730 PK3677_T

10-18

Note for Contactless 79/RT/E7900 Series

customers:
Statement according to FCC part 15.105
This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reason-

able protection against harmful interference

in a residential installation. This equipment

generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interfer-

ence will not occur in a particular installation.

If this equipment does cause harmful interfer-

ence to radio or television reception, which

can be determined by turning the equipment

off and on, the user is encouraged to try to

correct the interference by one or more of the

following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equip-

ment and receiver.

• Consult the dealer or an experienced radio/

TV technician for help.

Statement according to FCC part 15.21
Modifications not expressly approved by dor-

makaba could void the user’s authority to

operate the equipment.
Statement according to FCC part 15.19
This device complies with part 15 of the

FCC rules and Industry Canada ICES-003.

Operation is subject to the following two con-

ditions: (1) This device may not cause harmful

interference, and (2) this device must accept

any interference received, including interfer-

ence that may cause undesired operation.
Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1)

l’appareil ne doit pas produire de brouillage,

et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre

le fonctionnement.

Lever handle and card reader for fire exit hard-

ware
Clasified by Underwriters Laboratories Inc.

Intended for installation on mortise, rim or ver-

tical rod type devices.

Summary of Contents for 630 Series























Search results

Summary of Contents for 630 Series

Reviews:

Related manuals for 630 Series

Brands by name

Popular brands

Dormakaba 630 Series, Installation Instructions Manual

Search results

Summary of Contents for 630 Series

Reviews:

Related manuals for 630 Series

Brands by name

Popular brands