Doosan DP158LCF Operation & Maintenance Manual Download Page 98

Page: 98 / 160

8. Fuel system

136

Actuator

Actuator Component Parts Function

DV2213103B

DV2213104B

1. Emergency stop lever: The manual engine stop lever

when emergency.

2. Upper control chamber: The cover is install for inside

control.

3. Electronic control chamber: The electronic signal oper-

ates the operation lever. It is sealed and can not

control.

4. Adjusting screw: Adjusting screw is the controlled

max. fuel capacity. If the length of the nut is long, the

torque is decrease. if the the length of the nut is short,

the torque is increase.

5. Fuel stop plate: The plate controls the increasing fuel

as the preventing movement of adjusting screw.

6. Operation lever: It is the connecting lever to operate

the fuel rack.

7. Fuel rack: It controls the fuel capacity of the fuel injec-

tion pump connected link lever.

Fuel

injection

Pump

Emergenc

stop lever

Upper control chamber

(oil lubrication)

Electronic control

chamber

Ghana Actuator

e view

Operating lever

Stop Screw

Lock nut

Fuel rack

justing Screw

Lock nut

Fuel rack stop position

Top view

Linkage length(L)

Fuel rack stop position a

justment

CAUTION

Adjusting fuel injection pump is critical part for the

enfine performance and durability. Only certified

professional technicians should repair and maintain

engines.

Summary of Contents for DP158LCF

































































































































































Search results

Summary of Contents for DP158LCF

Reviews:

Doosan DP158LCF, Operation & Maintenance Manual, Page: 98 / 160

Search results

Summary of Contents for DP158LCF

Reviews: