manualshive.com logo in svg

Doosan DP158LCF, Operation & Maintenance Manual, Page: 102 / 160

Share
Download
Doosan DP158LCF Operation & Maintenance Manual Download Page 102

8. Fuel system

 140

Note) With (5) Speed Ramping biased to counterclock-

wise direction, a symptom of overshoot or hunting 

can occur.

3) Start cranking the engine.

5. Rated speed & Idle speed

1) Rated speed adjustment.

Note) After engine startup, remove the connection

between terminals G and M (with idle switch OFF)

Note) Under no load condition, adjust Speed. Clockwise): 

RPM increase/counterclockwise RPM decrease

2) Idle speed adjustment

Note) With idle switch ON again, set the engine speed

at 800 rpm by (6) Idle potentiometer.

Note) Reason for adjustment: To adjust pre-heat levels 

after engine start up or the initial fuel amount at 

engine start up

Note) Recommended position: Between the 12 and 3 

o'clock positions. Though varying by engine model 

or rated RPM, it is recommended to set the RPM 

as 800RPM.

Note) Possible problems: Decreasing cold start perfor-

mance and the excessive use of fuel during the 

warm-up phase.

6. Governor performance adjustment

1) Remove the connection between terminals G and M

(with idle switch OFF). Once the engine reaches run

speed, adjust the performance of governor.

DV2213196B

2) Gain adjustment.

Note) Turn (2) Gain clockwise until instability develops at

no load.

Note) Gradually move (2) Gain counterclockwise until 

stability returns.

Note) Move (2) Gain counterclockwise further by around 

20 minutes (10°) to ensure stable performance.

3) Stability adjustment.

Note) Turn (3) Stability clockwise at no load until insta-

bility develops.

Note) Gradually move (3) Stability counterclockwise until 

stability returns.

Note) Move (3) Stability counterclockwise further by 

around 20 minutes (10°) to ensure stable perfor-

mance.

7. Accessory adjustment

DV2213196C

1) Run Lamp ON

Note) At the rated speed, turn (10) Run counterclockwise

until the Run Lamp is on.

Note) Move (10) Run counterclockwise further by 90

°

 to 

prevent the Run Lamp from flickering.

2) Crank Lamp ON

Note) At the idle speed, turn (10) Crank counterclockwise

until the Crank Lamp is on.

Note) Move (10) Crank counterclockwise further by 90

°

 to 

prevent the Crank Lamp from flickering.

3) Overspeed Lamp ON

Note) At the rated speed, as pressing the Test button,

gradually turn (9) Over Speed counterclockwise 

until the Overspeed Lamp is on and the engine is 

shut off simultaneously.

CAUTION

Idle speed is one of the important factors to deter-

mine the characteristics of engine startup. Therefore, 

it is necessary to adjust the idle speed after rated 

speed adjustment regardless of the use of "idle 

mode."

Summary of Contents for DP158LCF

































































































































































Reviews:

No comments