manualshive.com logo in svg

Doosan DP158LCF, Operation & Maintenance Manual, Page: 100 / 160

Share
Download
Doosan DP158LCF Operation & Maintenance Manual Download Page 100

8. Fuel system

 138

Controller system

DGC-2013 Governor Controller System

DV2213203B

Description

DGC-2013 Governor Controller Unit is an electronic 

device designed based on PID algorithm to control engine 

speed with fast and precise response to transient load 

changes. The device is available for both single operation 

(Isochronous mode) and parallel operation (Droop mode).

Mounting & Warning

DGC-2013 Governor Controller Unit is an electronic 

device designed based on PID algorithm to control engine 

speed with fast and precise response to transient load 

changes. The device is available for both single operation 

(Isochronous mode) and parallel operation (Droop mode).

1. Mount the controller unit vertically to the surface of a

control cabinet, protected from the weather and high

humidity, and do not expose the controller unit to the

source of radiant heat. Prolonged exposure to mois-

ture (for one month or longer or in case condensation

forms) can lead to change in the resistance of internal

circuit and failure to reach rated torque. Therefore,

make sure that the controller is dry before use.

2. Do not rely exclusively on the governor system electric

actuator to prevent overspeed. A secondary shutoff

device, such as a fuel solenoid must be used.

3. The setting range indicated on each menu of the

control mode is the average range for each engine.

It is recommended to set DI engines within each indi-

cated setting range.

9

8

7

G

H

J

F

E

D

C

B

A

Battery

-

Actuator

P

ic

k-

up

S

pee

d T

rim

+

N

M

L

K

D

roop

A

UX

P

10

V

Id

le

6

5

4

3

2

1

O

FF

D1

D2

O

N

Cran

k

R

un

O

v

er

 

spee

d

P

o

w

er

P

ic

k-

up

Cran

k

R

un O

v

er

 

spee

d

T

est

S

tarting

F

uel

S

pee

d

R

amping

Id

le

D

roop

G

ain

S

tability

S

pee

d

±

°

¯

©

¨

§

¦

ª

­

¬

«

£

¤

¥

GND

F

rame

®

Summary of Contents for DP158LCF

































































































































































Reviews:

No comments