background image

# 2204 PRINCETON STAIR BUNK

SLATE - GREY

1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not

remove warning label from bed.

2. Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of

entrapment or falls.

3. Surface of mattress must be at least 5 inches (127mm) below the upper edge of guardrails.

4. Do not allow children under 6 years of age to use the upper bunk.

5. Prohibit more than one person on the upper bunk.

6. Periodicall, check and ensure that the guardrail, ladder, and other components are in their proper position,

free from damage, and that all connectors are tight.

7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.

8. Always use the ladder for entering and leaving the upper bunk.

9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

10. Use of a nightlight may provide added safety precaution for a child using the upper bunk.

11. Always use guardrail on both long sides of the upper bunk. If bunk bed will be placed next to the wall, the

guardrail the runs the full length of the bed should be place against the wall to prevent entrapment between

the bed and wall.

12. The use of water or sleep flotation mattresses is prohibited.

13. Keep these instruction for future reference.

SAFETY WARNINGS

STRANGULATION HAZARD -

Never attach or hang items to any part of the bunk bed that are not

designed for use with the bed ; for example, but not limited to, hooks, belts and jump ropes.

SIZE OF MATTRESS AND FOUNDATION

Use only mattress, foundation and desk combined which is 74 - 75 inches long and 37

1

2

 - 38

1

2

 inches wide on

upper bunk.
Ensure thickness of mattress and foundation combined does not exceed 8

1

2

 inches and mattress and is at

least 5 inches below edge of guardrails.

Replacement parts, may be obtained from any Donco dealer or directly from us at the below address.

DONCO TRADING COMPANY

Fort Worth, Texas 76140

Summary of Contents for PRINCETON STAIR BUNK 2204













Reviews: