Donaldson Torit Dalamatic Cased DLMC 1/2/15 Installation And Operation Manual Download Page 10 | Manualshive

Page: 10 / 36

Donaldson Torit Dalamatic Cased DLMC 1/2/15 Installation And Operation Manual Download Page 10

7

Donaldson Company, Inc.

Standard Equipment

Dalamatic Cased dust collectors are delivered partially

assembled in sections compatible with truck capacity

and load restrictions. All models require field assembly of

the leg, hopper, filter section, compressed air manifold,

and ducts.

leg and crossbrace

hopper

cabinet ground lug

(optional, not shown)

tubesheet (seal frame)

filter bag and cage (insert)

dirty-air inlet

clean-air outlet

solenoid enclosure

top inspection

panel

blow pipe (jet tube)

lifting lug

Typical Installation

(Collector shown with rear inlet and front outlet. Other options include side inlets and outlets and a top outlet to be

used with a mounted TBI fan.)

Typical systems include one of several hopper

arrangements designed for compatibility with various

solids-handing containers. A typical DLMC also has a

steel structure to support the collector.

«
...
8
9
10
11
12
...
»

Summary of Contents for Dalamatic Cased DLMC 1/2/15





































Reviews:

No comments