background image

 

 

13

5

 

OPERATION 

The 

Sanit

 range of hot water tanks is specially designed for use with a wide range of solar power 

elements, heat pumps and boilers powered by any type of fuel. 
If the tank is connected to a DOMUSA TEKNIK brand heating boiler, the boiler will be equipped with a 

summer or winter position switch, which is used to choose between: 

Summer position 

:

 in this position the boiler will only produce hot water as needed. The burner 

and feed pump of the storage heater (summer pump) will be switched on until the hot water stored 
reaches the temperature set on the hot water thermostat of the storage heater 

(2)

. When this 

temperature is reached, the burner and the summer pump will switch off. 

Winter position 

:

 in this position the boiler will produce hot water as needed and will also cater 

for the heating installation, giving priority to hot water production. 

6

 

DIAGRAM AND ELECTRICAL CONNECTION  

The 

Sanit

 range of hot water tanks is especially designed for easy electrical connection to a wide range 

of heating boilers. The special design of its electrical connections enables the boiler/hot water tank 

unit to provide heating and domestic hot water with automatic functioning, incorporating a hot water 

priority function to the joint operation of the two appliances. 
When installing the supply cable, take the hot water tank element into account. Different tanks may 

have different elements, and a different cable diameter is recommended for each type: 

Element Cable 

diameter

1500w 1.5 

mm

2

 

2500w 2.5 

mm

2

 

3500w 4 

mm

2

 

6.1

 

Electrical diagram 

The electrical connection of 

Sanit

 hot water tank must be made by qualified staff, and any 

modifications may only be made by the official technical assistance service. 

7

R: Máx. 3.500 W

Orange

White

Red

Brown

Blue

Grey

Black

T

ACS

2

5

O

/I

Blue

Black

Brown

T       tube for

DHW

conection to
boiler

Ph

N

~220/230 V

1

4

2

1

6

5

4

3

2

1

 

 E: 

Support element, maximum 3500 W.

 

 O/I: 

Support element switch.

 

 

T

DHW

:

  Domestic hot water thermostat. 

 

Summary of Contents for SANIT 1000

































Reviews: