Doka Staxo 40 Instructions For Assembly And Use Download Page 40

Page: 40 / 92

999805002 - 09/2018

Assembling towers in the upright

User Information

Load-bearing tower Staxo 40

Assembling towers in the upright

Assembling towers in the upright with 'mounted-ahead' 1.20m frames

As a rule:

▪

In this erection method, the horizontal profile of the

Staxo 40 frame 1.20m must always be on top, to

ensure fall protection.

▪

Slide the diagonal cross onto the safety-catch bolt

and immediately secure it with the safety catch.

Installation example with Staxo 40 screw-jack foot

30cm and Staxo 40 4-way screw-jack head 30cm.

Erecting the first storey

➤

Insert screwjack base units.

➤

Connect the frames together with diagonal crosses.

➤

Insert Staxo 40 couplers.

Note:

If it is intended to crane-lift the tower, the frames must

all be linked in a crane-handling-safe manner by

Staxo

40 tube connectors D48.3mm. See also the sec-

tion entitled 'Lifting by crane'.

NOTICE

▪

Erect the load-bearing tower in the vertical

on ground that is statically capable of sup-

porting the load.

▪

If the load-bearing tower is over 6

m high,

back-stay it or combine it with other towers.

98024-207-02

98024-270-01

Diagonal cross

98024-267-01

98024-266-01

98024-213-02

Summary of Contents for Staxo 40





























































































Search results

Summary of Contents for Staxo 40

Reviews:

Related manuals for Staxo 40

Brands by name

Popular brands

Doka Staxo 40, Instructions For Assembly And Use

Search results

Summary of Contents for Staxo 40

Reviews:

Related manuals for Staxo 40

Brands by name

Popular brands