manualshive.com logo in svg

Dodge HORNET 2023, Owner'S Manual

Share
Download
Dodge HORNET 2023 Owner'S Manual Download Page 87

STARTING AND OPERATING

85

(Continued)

(Continued)

When Brake Service Mode work is complete, the following 

steps must be followed to reset the parking brake system 

to normal operation:

Ensure the vehicle is at a standstill.

Press the brake pedal with moderate force.

Apply the EPB Switch.

NOTE:

A dedicated message will appear in the instrument cluster 

display if Brake Service Mode cannot be deactivated.

AUTOMATIC TRANSMISSION  

You must press and hold the brake pedal while shifting out 

of PARK.

WARNING!

You can be badly injured working on or around a motor 

vehicle. Do only that service work for which you have 

the knowledge and the right equipment. If you have any 

doubt about your ability to perform a service job, take 

your vehicle to a competent mechanic.

WARNING!

Never use the PARK (P) position as a substitute for 

the parking brake. Always apply the parking brake 

fully when exiting the vehicle to guard against vehicle 

movement and possible injury or damage.

Your vehicle could move and injure you and others if 

it is not in PARK. Check by trying to move the gear 

selector out of PARK with the brake pedal released. 

Make sure the transmission is in PARK before exiting 

the vehicle.

It is dangerous to shift out of PARK or NEUTRAL (N) if 

the engine speed is higher than idle speed. If your 

foot is not firmly pressing the brake pedal, the 

vehicle could accelerate quickly forward or in 

reverse. You could lose control of the vehicle and hit 

someone or something. Only shift into gear when the 

engine is idling normally and your foot is firmly 

pressing the brake pedal.

The vehicle may not engage a newly selected gear 

when shifting between PARK, REVERSE (R), or 

DRIVE (D) if the vehicle is moving while shifting.

Unintended movement of a vehicle could injure 

those in or near the vehicle. As with all vehicles, you 

should never exit a vehicle while the engine is 

running. Before exiting a vehicle, always come to a 

complete stop, then apply the parking brake, shift 

the transmission into PARK, and turn the ignition 

OFF. When the ignition is in the OFF position, the 

transmission is locked in PARK, securing the vehicle 

against unwanted movement.

When leaving the vehicle, always make sure the igni

-

tion is in the OFF position, remove the key fob from 

the vehicle, and lock the vehicle.

WARNING!

Never leave children alone in a vehicle, or with 

access to an unlocked vehicle. Allowing children to 

be in a vehicle unattended is dangerous for a 

number of reasons. A child or others could be seri

-

ously or fatally injured. Children should be warned 

not to touch the parking brake, brake pedal or the 

transmission gear selector.

Do not leave the key fob in or near the vehicle (or in 

a location accessible to children), and do not leave 

the ignition in the ON/RUN position. A child could 

operate power windows, other controls, or move the 

vehicle.

CAUTION!

Damage to the transmission may occur if the following 

precautions are not observed:

Shift into or out of PARK or REVERSE only after the 

vehicle has come to a complete stop.

Do not shift between PARK, REVERSE, NEUTRAL, or 

DRIVE when the engine is above idle speed.

Before shifting into any gear, make sure your foot is 

firmly pressing the brake pedal.

WARNING!

4

23_GG_OM_EN_USC_t.book  Page 85  

Summary of Contents for HORNET 2023

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands