manualshive.com logo in svg

Dodge HORNET 2023, Owner'S Manual

Share
Download
Dodge HORNET 2023 Owner'S Manual Download Page 76

74

GETTING TO KNOW YOUR INSTRUMENT PANEL

 

Fuel Level Sensor Failure Warning Light

This light illuminates when there is a fuel level 

sensor failure. If this light illuminates, take it to 

an authorized dealer and have them inspect it.

Active Speed Limiter Fault Warning Light — 

If Equipped

This warning light will illuminate to signal when 

there is a fault detected with the Active Speed 

Limiter.

Blind Spot Detection Fault Warning Light

This light alerts the driver that there is a fault in 

the Blind Spot Detection system.

Anti-Lock Brake System (ABS) Warning 

Light  

This warning light monitors the ABS. The light 

will turn on when the ignition is placed in the 

ON/RUN position and may stay on for as long 

as four seconds.

If the ABS light remains on or turns on while driving, then 

the Anti-Lock portion of the brake system is not 

functioning and service is required as soon as possible. 

However, the conventional brake system will continue to 

operate normally, assuming the Brake Warning Light is not 

also on.
If the ABS light does not turn on when the ignition is placed 

in the ON/RUN position, have the brake system inspected 

by an authorized dealer.

Drowsy Driver Detected System Fault 

Warning Light — If Equipped

This warning light will illuminate when the 

Drowsy Driver Detected (DDD) system is not 

operating correctly and requires service. 

Please see an authorized dealer.

Electric Park Brake Warning Light

This warning light will illuminate to indicate the 

Electric Park Brake is not functioning properly 

and service is required. Contact an authorized 

dealer.

Electronic Stability Control (ESC) Active 

Warning Light — If Equipped

This warning light will indicate when the

ESC system is Active. The ESC Indicator Light in 

the instrument cluster will come on when the 

ignition is placed in the ON/RUN position, and 

when ESC is activated. It should go out with the engine 

running. If the ESC Indicator Light comes on continuously 

with the engine running, a malfunction has been detected 

in the ESC system. If this warning light remains on after 

several ignition cycles, and the vehicle has been driven 

several miles (kilometers) at speeds greater than 30 mph 

(48 km/h), see an authorized dealer as soon as possible 

to have the problem diagnosed and corrected.

The ESC OFF Indicator Light and the ESC Indicator Light 

come on momentarily each time the ignition is placed 

in the ON/RUN position.

The ESC system will make buzzing or clicking sounds 

when it is active. This is normal; the sounds will stop 

when ESC becomes inactive.

This light will come on when the vehicle is in an 

ESC event.

Electronic Stability Control (ESC) OFF 

Warning Light — If Equipped

This warning light indicates the

ESC is off.

Each time the ignition is turned to ON/RUN, the ESC 

system will be on, even if it was turned off previously.

Fuel Cutoff Warning Light — If Equipped

This warning light will illuminate after an 

accident has occurred, and the system has 

shut the fuel off.

Fuel Cutoff Failure Warning Light — 

If Equipped

This light will illuminate if there is a fuel cutoff 

failure. If this light illuminates, take it to an 

authorized dealer and have them inspect it.

Fuel Level Sensor Failure Warning Light

This light illuminates when there is a fuel level 

sensor failure. If this light illuminates, take it to 

an authorized dealer and have them inspect it.

23_GG_OM_EN_USC_t.book  Page 74  

Summary of Contents for HORNET 2023

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands