manualshive.com logo in svg

Dodge HORNET 2023, Owner'S Manual

Share
Download
Dodge HORNET 2023 Owner'S Manual Download Page 73

GETTING TO KNOW YOUR INSTRUMENT PANEL

71

The battery was recently replaced and was not charged 

completely.

The battery was discharged by an electrical load left on 

when the vehicle was parked.

The battery was used for an extended period with the 

engine not running to supply radio, lights, chargers, 

+12 Volts portable appliances like vacuum cleaners, 

game consoles and similar devices.

What to do when an electrical load reduction action 

message is present (“Battery Saver On” or

“Battery Saver Mode”)
During a trip:

Reduce power to unnecessary loads if possible:

Turn off redundant lights (interior or exterior)

Check what may be plugged into power outlets 

+12 Volts, 150W, USB ports

Check HVAC settings (blower, temperature)

Check the audio settings (volume)

After a trip:

Check if any aftermarket equipment was installed 

(additional lights, upfitter electrical accessories, 

audio systems, alarms) and review specifications if any 

(load and Ignition Off Draw currents).

Evaluate the latest driving cycles (distance, driving 

time and parking time).

The vehicle should have service performed if the 

message is still present during consecutive trips and 

the evaluation of the vehicle and driving pattern did not 

help to identify the cause.

WARNING LIGHTS AND MESSAGES

The warning/indicator lights will illuminate in the 

instrument panel together with a dedicated message and/

or acoustic signal when applicable. These indications are 

indicative and precautionary and as such must not be 

considered as exhaustive and/or alternative to the 

information contained in the Owner’s Manual, which you 

are advised to read carefully in all cases. Always refer to 

the information in this chapter in the event of a failure 

indication. All active telltales will display first if applicable. 

The system check menu may appear different based upon 

equipment options and current vehicle status. Some 

telltales are optional and may not appear.

R

ED

 W

ARNING

 L

IGHTS

Air Bag Warning Light

This warning light will illuminate to indicate a 

fault with the air bag, and will turn on for four to 

eight seconds as a bulb check when the 

ignition is placed in the ON/RUN position. This 

light will illuminate with a single chime when a fault with 

the air bag has been detected, it will stay on until the fault 

is cleared. If the light is either not on during startup, stays 

on, or turns on while driving, have the system inspected at 

an authorized dealer as soon as possible.

Brake Warning Light  

This warning light monitors various brake 

functions, including brake fluid level and 

parking brake application. If the brake light 

turns on it may indicate that the parking brake 

is applied, that the brake fluid level is low, or that there is 

a problem with the Anti-Lock Brake System reservoir.

If the light remains on when the parking brake has been 

disengaged, and the fluid level is at the full mark on the 

master cylinder reservoir, it indicates a possible brake 

hydraulic system malfunction or that a problem with the 

Brake Booster has been detected by the Anti-Lock Brake 

System (ABS) / Electronic Stability Control (ESC) system. 

In this case, the light will remain on until the condition has 

been corrected. If the problem is related to the brake 

booster, the ABS pump will run when applying the brake, 

and a brake pedal pulsation may be felt during each stop.
The dual brake system provides a reserve braking capacity 

in the event of a failure to a portion of the hydraulic 

system. A leak in either half of the dual brake system is 

indicated by the Brake Warning Light, which will turn on 

when the brake fluid level in the master cylinder has 

dropped below a specified level.
The light will remain on until the cause is corrected.

NOTE:

The light may flash momentarily during sharp cornering 

maneuvers, which change fluid level conditions. The 

vehicle should have service performed, and the brake 

fluid level checked.
If brake failure is indicated, immediate repair is necessary.

WARNING!

Driving a vehicle with the red brake light on is 

dangerous. Part of the brake system may have failed. 

It will take longer to stop the vehicle. You could have a 

collision. Have the vehicle checked immediately.

3

23_GG_OM_EN_USC_t.book  Page 71  

Summary of Contents for HORNET 2023

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands