Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 366 | Manualshive

Page: 366 / 427

background image

CAUTION!

Using axle fluid other than the manufactured recom-
mended fluid may cause a shudder/noise issue. refer
to “Fluids, Lubes, And Genuine Parts” in “ Maintain-
ing Your Vehicle” for further information.

Change Axle Lubricant

Refer to “Maintenance Schedule” for the proper mainte-
nance intervals. Change the lubricant immediately if
contaminated with water. See your authorized dealer for
service.

Appearance Care And Protection From Corrosion

Protection Of Body And Paint From Corrosion

Vehicle body care requirements vary according to geo-
graphic locations and usage. Chemicals that make roads
passable in snow and ice, and chemicals that are sprayed
on trees and road surfaces during other seasons, are

highly corrosive to the metal in your vehicle. Outside
parking, which exposes your vehicle to airborne contami-
nants, road surfaces on which the vehicle is operated,
extreme hot or cold weather and other extreme condi-
tions will have an adverse effect on paint, metal trim, and
underbody protection.

The following maintenance recommendations will enable
you to obtain maximum benefit from the corrosion
resistance built into your vehicle.

Washing

•

Wash your vehicle regularly. Always wash your ve-
hicle in the shade using MOPAR Car Wash, or a mild
car wash soap, and rinse the panels completely with
clear water.

•

If insects, tar, or other similar deposits have accumu-
lated on your vehicle, use MOPAR Super Kleen Bug
and Tar Remover to remove.

364

MAINTAINING YOUR VEHICLE

«
...
364
365
366
367
368
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: OEM Tools Pages: 4

Brand: K&M Pages: 3

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Brand: Mazdaspeed Pages: 8

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: Yakima Pages: 21

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

2003 Silhouette

Brand: Oldsmobile Pages: 466

Brand: AL-KO Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands