manualshive.com logo in svg

Dodge 2016 Viper SRT ACR, Owner'S Manual

The Dodge 2016 Viper SRT ACR Owner's Manual is a comprehensive guide that provides essential information for owners of this high-performance vehicle. Packed with crucial details and maintenance tips, this manual is available for free download at manualshive.com. Ensure you have the necessary knowledge to maximize your Viper's performance and longevity.

Share
Download
background image

of storage time without losing radio and engine control-
ler adaptive memory. Using this feature is an alternative
to disconnecting the battery.

NOTE:

This vehicle is designed to sit in storage with a

fully charged battery for up to 30 days. If you plan to
store the vehicle longer than 30 days, we recommend
doing one of the following:

•

Disconnect the battery.

•

Use the battery charger.

•

Put the vehicle into Hibernation mode (3-month
charge).

To Activate Hibernation Mode

1. Cycle the ignition switch to (ACC).

2. Select Hibernation mode within the Driver Informa-

tion Display (DID).

3. Push the right arrow button on the steering wheel

controls for one second. Vehicle will countdown from
ten seconds and enter Hibernation Mode.

NOTE:

You may push the right arrow button on the

steering wheel controls during the countdown to abort
Hibernation Mode.

To Deactivate Hibernation Mode

1. Push the RKE UNLOCK button to unlock the vehicle.

2. Push the ignition switch to the ON/RUN position.

Air Conditioner Maintenance

For best possible performance, your air conditioner
should be checked and serviced by an authorized dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a performance
test. Drive belt tension should also be checked at this
time.

348

MAINTAINING YOUR VEHICLE

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Brand: GMC Pages: 140
Oldsmobile 2004 Alero Owner'S Manual preview
2004 Alero
Brand: Oldsmobile Pages: 360
Parrot CK3300 Setup Information Manual preview
CK3300
Brand: Parrot Pages: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Brand: Parrot Pages: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Brand: Parrot Pages: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Brand: Parrot Pages: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Brand: Parrot Pages: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Brand: Parrot Pages: 106
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Brand: Quadratec Pages: 20
PAC GM1A-R Quick Start Manual preview
GM1A-R
Brand: PAC Pages: 4
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Brand: APS Pages: 3
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Brand: Saturn Pages: 440
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Brand: Lantronix Pages: 51
S&B Filters 75-5053 Installation Instructions preview
75-5053
Brand: S&B Filters Pages: 4
Mazda 2016 CX3 Service Information preview
2016 CX3
Brand: Mazda Pages: 3
Toyota Solara guide Owner'S Manual preview
Solara guide
Brand: Toyota Pages: 497
Edelbrock 29135 Installation Instructions preview
29135
Brand: Edelbrock Pages: 2
Mercedes-Benz 1989 560 SL Owner'S Manual preview
1989 560 SL
Brand: Mercedes-Benz Pages: 93

Brands by name

Popular brands

Load more brands