Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 335 | Manualshive

Page: 335 / 427

background image

CAUTION!

Accessories plugged into the vehicle power outlets
draw power from the vehicle’s battery, even when not
in use (i.e., cellular devices, etc.). Eventually, if
plugged in long enough without engine operation,
the vehicle’s battery will discharge sufficiently to
degrade battery life and/or prevent the engine from
starting.

FREEING A STUCK VEHICLE

If your vehicle becomes stuck in mud, sand, or snow, it
can often be moved using a rocking motion. Turn your
steering wheel right and left to clear the area around the
front wheels. Then shift back and forth between 1st gear
and REVERSE, while gently pushing the accelerator.

Use the least amount of pressure to maintain the rocking
motion, without spinning the wheels, or racing the
engine.

CAUTION!

•

When “rocking” a stuck vehicle by shifting be-
tween 1st gear and REVERSE, do not spin the
wheels faster than 15 mph (24 km/h), or drivetrain
damage may result.

•

Revving the engine or spinning the wheels too fast
may lead to transmission overheating and failure.
It can also damage the tires. Do not spin the wheels
above 30 mph (48 km/h) while in gear (no trans-
mission shifting occurring).

6

WHAT TO DO IN EMERGENCIES

333

«
...
333
334
335
336
337
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: CAMPARK Pages: 20

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

Brand: Oldsmobile Pages: 360

Brand: IAG Pages: 3

Brand: Prorack Pages: 14

Brand: MAXWORKS Pages: 7

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Subaru Pages: 19

Brand: Saab Pages: 15

Brand: Lantronix Pages: 51

Brand: Xingyun Pages: 74

Brand: Rigid Hitch Pages: 2

Prestige 128-8602

Brand: Audiovox Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands