Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 322

Page: 322 / 427

Tire Service Kit Components And Operation

Using The Mode Select Knob And Hoses

Your Tire Service Kit is equipped with the following
symbols to indicate the air or sealant mode.

Selecting Air Mode

Push in the Mode Select Knob (5) and turn to this
position for air pump operation only. Use the

Black Air Pump Hose (7) when selecting this mode.

Selecting Sealant Mode

Push in the Mode Select Knob (5) and turn to this
position to inject the Tire Service Kit Sealant and

to inflate the tire. Use the Sealant Hose (clear hose) (6)
when selecting this mode.

Using The Power Button

Push and release the Power Button (4) once to

turn On the Tire Service Kit. Push and release the Power
Button (4) again to turn Off the Tire Service Kit.

Tire Service Kit Components

1 — Sealant Bottle

5 — Mode Select Knob

2 — Deflation Button

6 — Sealant Hose (Clear)

3 — Pressure Gauge

7 — Air Pump Hose (Black)

4 — Power Button

8 — Power Plug (located on the bot-
tom side of the Tire Service Kit)

320

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands

Dodge 2016 Viper SRT ACR, Owner'S Manual

Search results

Summary of Contents for 2016 Viper SRT ACR

Reviews:

Related manuals for 2016 Viper SRT ACR

Brands by name

Popular brands