Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 310 | Manualshive

Page: 310 / 427

background image

WARNING!

(Continued)

time the vehicle is raised. Have any abnormal
conditions repaired promptly. Until repaired, drive
with all side windows fully open.

ADDING FUEL

1. Push the fuel filler door release switch (located in the

driver’s door map pocket).

2. Open the fuel filler door.

NOTE:

In certain cold conditions, ice may prevent the

fuel door from opening. If this occurs, lightly push on the
fuel door to break the ice buildup and re-release the fuel
door using the inside release button. Do not pry on the
door.

3. There is no fuel filler cap. A flapper door inside the

pipe seals the system.

4. Insert the fuel nozzle fully into the filler pipe – the

nozzle opens and holds the flapper door while refuel-
ing.

NOTE:

Only the correct size nozzle opens the latches

allowing the flapper door to open.

5. Fill the vehicle with fuel – when the fuel nozzle

“clicks” or shuts off the fuel tank is full.

6. Remove the fuel nozzle and close the fuel door.

NOTE:

A funnel is provided (located in the trunk in the

spare tire area) to open the flapper door to allow for
emergency refueling with a gas can.

CAUTION!

To avoid fuel spillage and overfilling, do not “top
off” the fuel tank after filling.

308

STARTING AND OPERATING

«
...
308
309
310
311
312
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Mazda Pages: 4

CK 3000 Evolution

Brand: Parrot Pages: 2

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 2

Brand: Yakima Pages: 12

Brand: Taffio Pages: 8

Brand: FormFit Pages: 4

Brand: Rati Pages: 2

Hypercharger HYC 075

Brand: Alpitronic Pages: 64

Brand: Prorack Pages: 20

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

Brand: Improved Racing Pages: 17

Brand: Thule Pages: 12

2003 Silhouette

Brand: Oldsmobile Pages: 466

Brand: Honda Pages: 569

Brand: r.LiNK Pages: 20

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brand: Or-Fab Pages: 4

FABIA II TMB PS 035

Brand: Skoda Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands