manualshive.com logo in svg

Dodge 2016 Viper SRT ACR, Owner'S Manual

The Dodge 2016 Viper SRT ACR Owner's Manual is a comprehensive guide that provides essential information for owners of this high-performance vehicle. Packed with crucial details and maintenance tips, this manual is available for free download at manualshive.com. Ensure you have the necessary knowledge to maximize your Viper's performance and longevity.

Share
Download
background image

TIRE PRESSURE MONITOR SYSTEM (TPMS)

The Tire Pressure Monitor System (TPMS) uses wireless
technology with wheel rim mounted electronic sensors to
monitor tire pressure levels. Sensors mounted to each
wheel as part of the valve stem transmit tire pressure

readings to the receiver module. It is particularly impor-
tant for you to check the tire pressure in all of the tires on
your vehicle monthly and to maintain the proper pres-
sure. The TPMS consists of the following components:

•

Receiver module

•

Four TPM sensors

•

Various TPMS messages, which display in the Driver
Information Display (DID)

•

TPM Telltale Light

The Tire Pressure Monitor System (TPMS) will warn the
driver of a low tire pressure based on the vehicle recom-
mended cold placard pressure.

The tire pressure will vary with temperature by about
1 psi (7.0 kPa) for every 12°F (6.5°C). This means that
when the outside temperature decreases, the tire pressure
will decrease. Tire pressure should always be set based on

Tire Rotation

5

STARTING AND OPERATING

297

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

cam 2850 Mounting Instructions preview
2850
Brand: cam Pages: 2
Dapper Lighting 575 Install Manual preview
575
Brand: Dapper Lighting Pages: 2
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Yakima Q46 Installation Instructions preview
Q46
Brand: Yakima Pages: 4
Cadillac ESCALADE FAMILY - SPECIFICATIONS 2011 Specifications preview
ESCALADE FAMILY - SPECIFICATIONS 2011
Brand: Cadillac Pages: 1
Chevrolet Malibu 2014 Owner'S Manual preview
Malibu 2014
Brand: Chevrolet Pages: 428
Kuda 079020 Installation Instruction preview
079020
Brand: Kuda Pages: 2
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Brand: E&G Classics Pages: 2
Hummer HX-T Owner'S Manual preview
HX-T
Brand: Hummer Pages: 31
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Brand: Lexus Pages: 830
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Brand: AUTOTECH Pages: 4
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Brand: Easee Pages: 21
SkyRack SR-CB-101 Assembly And Instruction Sheet preview
SR-CB-101
Brand: SkyRack Pages: 2
Jaeger 12500628 Fitting Instructions Manual preview
12500628
Brand: Jaeger Pages: 17
ACV 381094-36-1 Install Manual preview
381094-36-1
Brand: ACV Pages: 12

Brands by name

Popular brands

Load more brands