Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 265 | Manualshive

Page: 265 / 427

background image

WARNING!

•

Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children to
be in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
injured seriously or fatally. Do not leave the key
fob in or near the vehicle (or in a location accessible
to children), and do not leave the ignition of a
vehicle equipped with Keyless Enter-N-Go in the
ACC or ON/RUN mode. A child could operate
power windows, other controls, or move the ve-
hicle.

•

Ensure the parking brake is fully disengaged be-
fore driving. Failure to do so can lead to brake
failure, and an accident.

BRAKE SYSTEM

Your vehicle is equipped with dual hydraulic
brake systems. If either of the two hydraulic
systems loses normal capability, the remaining
system will still function. However, there will

be some loss of overall braking effectiveness. You may
notice increased pedal travel during application, greater
pedal force required to slow or stop, and potential
activation of the “Brake System Warning Light.”

In the event power assist is lost for any reason (i.e.,
repeated brake applications with the engine off) the
brakes will still function. However, the effort required to
brake the vehicle will be much greater than that required
with the power system operating.

5

STARTING AND OPERATING

263

«
...
263
264
265
266
267
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Vauxhall Pages: 2

Brand: Warrior Products Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: PullRite Pages: 10

Brand: Phonocar Pages: 2

Brand: Ford Pages: 368

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: ULTIMATE SPEED Pages: 50

Brand: Tesla Pages: 274

Brand: Conrad Pages: 50

Brand: Kleinn Pages: 8

Brand: Ford Pages: 264

Brand: Rosco Pages: 12

Brand: Datsun Pages: 104

Brand: injen technology Pages: 3

Brand: Valeo Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands