Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 427

background image

To Arm The System

Follow these steps to arm the Vehicle Security Alarm:

1. Make sure the vehicle ignition system is in the

⬙

OFF

⬙

position.

2. Perform one of the following methods to lock the

vehicle:

•

Push the LOCK

button on the interior power

door lock switch with the driver and/or passen-
ger door open.

•

Push the LOCK the

button on the Remote

Keyless Entry (RKE) transmitter.

3. If any doors are open, close them.

Entering The Liftgate With The System Armed

NOTE:

Using the key to open the liftgate while the

Vehicle Security Alarm is armed will trigger the alarm.

Push the LIFTGATE

release button on the RKE

transmitter twice to allow access without triggering
the alarm or having to disarm the Vehicle Security
Alarm. Then, within 30 seconds, open the liftgate by
using the key cylinder or the LIFTGATE release switch
located in the exterior liftgate handle.

To Disarm The System

The Vehicle Security Alarm can be disarmed using any of
the following methods:

•

Push the UNLOCK

button on the Remote Keyless

Entry (RKE) transmitter.

•

Cycle the vehicle ignition system out of the OFF
position:

•

Push the Keyless Enter-N-Go Start/Stop button (re-
quires at least one valid Key Fob in the vehicle).

18

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
18
19
20
21
22
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Harbor Freight Tools Pages: 4

Brand: Yakima Pages: 6

Brand: Yakima Pages: 18

Brand: FORM FIT Pages: 2

01 29 9 416 497

Brand: BMW Pages: 5

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: MASCOT Pages: 12

Brand: Motoalliance Pages: 8

Brand: Abrams Pages: 12

Brand: SAFARI Pages: 5

Brand: Westin Pages: 3

2000 Accord Sedan

Brand: Honda Pages: 320

Brand: Belkin Pages: 30

Brand: Mitsubishi Pages: 141

Brand: Guardsman Pages: 2

Brand: Mazda Pages: 14

Brand: iDataLink Pages: 11

Prime Design AAL-8003

Brand: Safe Fleet Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands