Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 166 | Manualshive

Page: 166 / 427

background image

Loose Fuel Filler Cap Indicator Light — If Equipped

Yellow Telltale

Light

What It Means

Loose Fuel Filler Cap Indicator Light — If Equipped

This light will illuminate when fuel filler cap is loose. Properly close the filler cap to disen-
gage the light. If the light does not turn off, please see your authorized dealer.

Tire Pressure Monitoring Indicator Light

Yellow Telltale

Light

What It Means

Tire Pressure Monitoring Indicator Light

The warning light switches on and a message is displayed to indicate that the tire pressure
is lower than the recommended value and/or that slow pressure loss is occurring. In these
cases, optimal tire duration and fuel consumption may not be guaranteed.
Should one or more tires be in the condition mentioned above, the display will show the
indications corresponding to each tire in sequence.

164

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
164
165
166
167
168
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Green Motion DC 22

Brand: Eaton Pages: 65

Brand: Uebler Pages: 18

Brand: Triumph Pages: 86

Brand: Whispbar Pages: 15

Brand: Whispbar Pages: 77

01 29 9 416 497

Brand: BMW Pages: 5

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Cadillac Pages: 34

Brand: Whispbar Pages: 14

Brand: RBO Pages: 15

Brand: RAM Pages: 330

Brand: Lock'er Down Pages: 2

Brand: Goobay Pages: 2

Brand: JBA Pages: 5

Brand: Volvo Pages: 5

Brand: Proxel Pages: 16

Brand: American muscle Pages: 3

Brand: GMC Pages: 364

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands