Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 131 | Manualshive

Page: 131 / 427

background image

Reprogramming A Single HomeLink Button
(Rolling Code)

To reprogram a channel that has been previously trained,
follow these steps:

1. Cycle the ignition to the ON/RUN position.

2. Push and hold the desired HomeLink button until the

indicator light begins to flash after 20 seconds.

Do not

release the button.

3.

Without releasing the button

proceed with “Program-

ming A Rolling Code” step 2 and follow all remaining
steps.

Programming A Non-Rolling Code

For programming Garage Door Openers manufactured
before 1995.

1. Cycle the ignition to the ON/RUN position.

2. Place the hand-held transmitter 1 to 3 inches (3 to 8

cm) away from the HomeLink button you would like
to program while keeping the HomeLink indicator
light in view.

3. Push and hold the HomeLink button you want to

program while you push and hold the hand-held
transmitter button.

4. Continue to hold both buttons and observe the indi-

cator light. HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the fre-
quency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from
slow to rapid.

5. Push and hold the programmed HomeLink button

and observe the indicator light.

•

If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink button is pressed.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

129

«
...
129
130
131
132
133
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: Abarth Pages: 176

witty park XEV6 Series

Brand: hager Pages: 9

Brand: FormFit Pages: 2

Brand: MAXWORKS Pages: 7

Brand: RAM Pages: 496

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Navman Pages: 10

Brand: Macrom Pages: 10

Brand: Honda Pages: 22

Brand: Mercedes-Benz Pages: 494

2007 SLR Mclaren

Brand: Mercedes-Benz Pages: 425

Brand: WABCO Pages: 224

Brand: QA1 Pages: 3

Brand: Opel Pages: 44

Brand: Setma Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands