Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 123 | Manualshive

Page: 123 / 427

background image

To Deactivate

A soft tap on the brake pedal, pushing the CANCEL
button, manually accelerating 10 mph (16 km/h) above
the set speed or normal brake pressure while slowing the
vehicle will deactivate the Electronic Speed Control with-
out erasing the set speed memory.

Pushing the ON/OFF button or turning the ignition
switch OFF erases the set speed memory.

To Resume Speed

To resume a previously set speed, push the RES (+)
button and release. Resume can be used at any speed
above 20 mph (32 km/h).

To Vary The Speed Setting

To Increase Speed

When the Electronic Speed Control is set, you can in-
crease speed by pushing the RES (+) button.

The drivers preferred units can be selected through the
instrument panel settings if equipped. Refer to “Under-
standing Your Instrument Panel” for more information.
The speed increment shown is dependent on the selected
speed unit of U.S. (mph) or Metric (km/h):

U.S. Speed (mph)

•

Pushing the RES (+) button once will result in a 1 mph
increase in set speed. Each subsequent tap of the
button results in an increase of 1 mph.

•

If the button is continually pushed, the set speed will
continue to increase until the button is released, then
the new set speed will be established.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

121

«
...
121
122
123
124
125
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: JETBAG Pages: 44

Titanium Series

Brand: Fass Pages: 13

Green Motion DC 22

Brand: Eaton Pages: 65

Brand: Jeep Pages: 25

Brand: Kargo Master Pages: 5

CK 3000 Evolution

Brand: Parrot Pages: 2

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Brand: JANE Pages: 21

Brand: Whispbar Pages: 16

Brand: Ford Pages: 37

Brand: V8 equipment Pages: 17

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: Subaru Pages: 21

Brand: GMC Pages: 20

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: Caltrend Pages: 2

Brand: Advanced ICE Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands