Dodge 2012 Charger Owner'S Manual Download Page 227

Page: 227 / 594

NOTE:

Any chassis/suspension modifications to the

vehicle will effect the performance of the Adaptive Cruise
Control.

Activating Adaptive Cruise Control (ACC)

You can only activate ACC if the vehicle speed is above
20 mph (32 km/h).

When the system is turned on and in the READY state,
the Electronic Vehicle Information Center (EVIC) dis-
plays “Adaptive Cruise Ready.”

When the system is OFF, the EVIC displays “Adaptive
Cruise Control Off.”

NOTE:

You cannot enable ACC under the following

conditions:

•

When you apply the brakes.

•

When the parking brake is set.

•

When the automatic transmission is in PARK, RE-
VERSE or NEUTRAL.

•

When pushing the RES

button without a previously

set speed in memory.

To Activate

Push and release the ON/OFF button. The ACC menu in
the EVIC displays “Adaptive Cruise Ready.”

Adaptive Cruise Control (ACC) Ready

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

225

Summary of Contents for 2012 Charger



















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 Charger

Reviews:

Related manuals for 2012 Charger

Brands by name

Popular brands

Dodge 2012 Charger, Owner'S Manual

Search results

Summary of Contents for 2012 Charger

Reviews:

Related manuals for 2012 Charger

Brands by name

Popular brands