Dodge 2012 Charger Owner'S Manual Download Page 184 | Manualshive

Page: 184 / 594

background image

Power Lumbar — If Equipped

Vehicles equipped with power driver or passenger seats
may be also be equipped with power lumbar. The power
lumbar switch is located on the outboard side of the power
seat. Push the switch forward or rearward to increase or
decrease the lumbar support. Push the switch upward or
downward to raise or lower the lumbar support.

Heated Seats — If Equipped

On some models, the front and rear seats may be
equipped with heaters in both the seat cushions and
seatbacks.

The front driver and passenger heated seats are operated
using the Uconnect Touch™ System.

WARNING!

•

Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, ex-
haustion or other physical condition must exercise
care when using the seat heater. It may cause burns
even at low temperatures, especially if used for
long periods of time.

(Continued)

Power Lumbar Switch

182

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
182
183
184
185
186
...
»

Summary of Contents for 2012 Charger



















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Charger

Brand: Kargo Master Pages: 5

Brand: U.S. General Pages: 5

Brand: Farad Pages: 8

Wireless Charging Station Universal

Brand: BMW Pages: 160

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

Brand: ECS Electronics Pages: 16

Brand: Audi Pages: 12

Brand: STC Pages: 6

Brand: Kuda Pages: 3

Brand: RAM Pages: 616

Brand: Nav TV Pages: 9

Brand: Honda Pages: 81

Brand: Toro Pages: 24

Truck Training Model

Brand: WABCO Pages: 56

Brand: VER-MAC Pages: 64

Hatch-bag Luggage System

Brand: Tabernus Peram Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands