Dodge 2011 Grand Caravan Owner'S Manual Download Page 481 | Manualshive

Page: 481 / 562

background image

CAUTION!

•

It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to
the negative post. Battery posts are marked posi-
tive (+) and negative (-) and are identified on the
battery case. Cable clamps should be tight on the
terminal posts and free of corrosion.

•

If a “fast charger” is used while the battery is in
the vehicle, disconnect both vehicle battery cables
before connecting the charger to the battery. Do
not use a “fast charger” to provide starting voltage.

Air Conditioner Maintenance

For best possible performance, your air conditioner
should be checked and serviced by an authorized dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a system
performance check. Drive belt tension should also be
checked at this time.

CAUTION!

Do not use chemical flushes in your air conditioning
system as the chemicals can damage your air condi-
tioning components. Such damage is not covered by
the New Vehicle Limited Warranty.

7

MAINTAINING YOUR VEHICLE

479

«
...
479
480
481
482
483
...
»

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

Brand: ZAPTEC Pages: 64

Brand: ZAPTEC Pages: 24

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Q'STRAINT Pages: 10

Brand: Ironton Pages: 7

Brand: Gatorback Mudflaps Pages: 4

Brand: Würth Pages: 36

Brand: tams elektronik Pages: 44

Brand: Ranger design Pages: 22

Quantum hardcoated N30216

Brand: National Cycle Pages: 3

Brand: Ford Pages: 256

Brand: Metra Electronics Pages: 8

Brand: Pyle Pages: 2

Brand: Weltmann KFZ-Teile Pages: 12

Brand: ECS Pages: 4

Brand: Whispbar Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands