Dodge 2011 Challenger Owner'S Manual Download Page 466 | Manualshive

Page: 466 / 490

background image

Temperature Grades

The temperature grades are A (the highest), B, and C,
representing the tire’s resistance to the generation of heat
and its ability to dissipate heat, when tested under
controlled conditions on a specified indoor laboratory
test wheel. Sustained high temperature can cause the
material of the tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance, which all
passenger car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades B and A repre-
sent higher levels of performance on the laboratory test
wheel, than the minimum required by law.

WARNING!

The temperature grade for this tire is established for
a tire that is properly inflated and not overloaded.
Excessive speed, under-inflation, or excessive load-
ing, either separately or in combination, can cause
heat buildup and possible tire failure.

464

IF YOU NEED CONSUMER ASSISTANCE

«
...
464
465
466
467
468
...
»

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Brand: ULTIMATE SPEED Pages: 19

Brand: VEAP SHIELD UNITED Pages: 3

Brand: Falcon Pages: 8

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: Ignition Pages: 1

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: Metra Electronics Pages: 20

Truck Training Model

Brand: WABCO Pages: 56

Brand: Jeep Pages: 292

Brand: Roadmaster Pages: 4

Multi Vehicle Mount MVM-35-05

Brand: Bracketron Pages: 4

Brand: Tesla Pages: 42

Brand: Mazda Pages: 196

Brand: Skoda Pages: 288

Brand: TrailPRO Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands