manualshive.com logo in svg

Dodge 2011 Challenger, Owner'S Manual

The Dodge 2011 Challenger is a powerhouse of a vehicle, providing an exhilarating driving experience. To ensure you get the most out of your Challenger, make sure to download the free user manual from manualshive.com. This manual offers detailed specifications and instructions to help you fully enjoy this iconic car.

Share
Download
background image

•

Press Brake & Push Button to Start

•

Push Button or Insert Key/Turn To Run (refer to
“Remote Starting System” in “Things To Know Before
Starting Your Vehicle”)

•

1–4 SKIPSHIFT

Engine Oil Change Indicator System

Oil Change Required

Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10 sec-
onds after a single chime has sounded, to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate, dependent
upon your personal driving style.

Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position or cycle the ignition to the ON/RUN position if
equipped with Keyless Enter-N-Go. To turn off the
message temporarily, press and release the MENU but-
ton. To reset the oil change indicator system (after
performing the scheduled maintenance) refer to the fol-
lowing procedure.

Vehicles Equipped With Keyless Enter-N-Go

1. Without pressing the brake pedal, push the ENGINE
START/STOP button and cycle the ignition to the ON/
RUN position (Do not start the engine.)

2. Fully depress the accelerator pedal, slowly, three times
within 10 seconds.

3. Without pressing the brake pedal, push the ENGINE
START/STOP button once to return the ignition to the
OFF/LOCK position.

192

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Eclipse AVN 2210p mkII Operation Manual preview
AVN 2210p mkII
Brand: Eclipse Pages: 6
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Brand: Mazda Pages: 12
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Brand: KRAFTWERK Pages: 2
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Brand: Raytel LLC Pages: 40
TATA Motors Sumo Victa EX Owner'S Manual & Service Book preview
Sumo Victa EX
Brand: TATA Motors Pages: 92
Sanitas SMG 245 Instructions For Use Manual preview
SMG 245
Brand: Sanitas Pages: 36
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Brand: ULTIMATE SPEED Pages: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Brand: Chevrolet Pages: 441
rockymounts SplitRailLS Installation Instructions Manual preview
SplitRailLS
Brand: rockymounts Pages: 6
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Brand: Anker Technology Pages: 8
Dodge Charger SRT 392 2017 Operating Information Manual preview
Charger SRT 392 2017
Brand: Dodge Pages: 576
Lexus LS 500h 2022 Owner'S Manual, Quick Manual preview
LS 500h 2022
Brand: Lexus Pages: 108
Renault CAPTUR 2019 Vehicle Instruction Card preview
CAPTUR 2019
Brand: Renault Pages: 11
Tobe EPS-LD SafePark Technical Data preview
EPS-LD SafePark
Brand: Tobe Pages: 2
Istar PI00670 Instruction Manual preview
PI00670
Brand: Istar Pages: 6
Mid America Motorworks 602-781 Instruction Sheet preview
602-781
Brand: Mid America Motorworks Pages: 2
Thule Follow me RAPID INTRACKER Fitting Instructions Manual preview
Follow me RAPID INTRACKER
Brand: Thule Pages: 8
XTC RZR-SW-USB-2B Manual preview
RZR-SW-USB-2B
Brand: XTC Pages: 2

Brands by name

Popular brands

Load more brands