Dodge 2006 Caravan Manual Download Page 169 | Manualshive

Page: 169 / 504

background image

Programming HomeLink

NOTE:

When programming a garage door opener, it is

advised to park outside the garage. Some vehicles may
require the ignition switch to be turned to the second (or

⬙

accessories

⬙

) position for programming and/or opera-

tion of HomeLink. It is also recommended that a new
battery be placed in the hand-held transmitter of the
device being programmed to HomeLink for quicker
training and accurate transmission of the radio-frequency
signal.

1. Press and hold the two outer HomeLink buttons, and
release only when the indicator light begins to flash (after
20 seconds).

Do not

hold the buttons for longer than 30

seconds and

do not

repeat step one to program a second

and/or third hand-held transmitter to the remaining two
HomeLink buttons.

2. Position the end of your hand-held transmitter 1-3
inches (3-8 cm) away from the HomeLink buttons while
keeping the indicator light in view.

HomeLink Buttons

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

169

3

«
...
167
168
169
170
171
...
»

Summary of Contents for 2006 Caravan

























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2006 Caravan

Brand: JANE Pages: 21

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: GATmatic Pages: 13

Brand: Trailboss Pages: 5

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: MAXWORKS Pages: 7

Brand: BURY Pages: 2

Brand: T-Mobile Pages: 2

Brand: RAM Pages: 13

TX-STAMP-4-FC04

Brand: Over Armour Offroad Pages: 9

Brand: Jeep Pages: 292

Brand: Billien Pages: 2

Brand: Lexus Pages: 28

Brand: Toyota Pages: 36

Brand: Nav TV Pages: 8

Brand: Haltech Pages: 13

Brand: Menabo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands