Dodge 2006 Caravan Manual Download Page 147 | Manualshive

Page: 147 / 504

background image

MULTIFUNCTION LEVER

Turn Signals

Move the Multifunction Lever up or down and the
arrows on each side of the base instrument cluster or
Information Center flash to indicate proper operation of
the front and rear turn signal lights. You can signal a lane
change by moving the lever partially up or down.

If either indicator flashes at a rapid rate, check for a
defective outside turn signal light bulb. If one of the
indicators fails to light when the lever is moved, it would
suggest that the indicator light is defective.

Turn Signal Warning

If the vehicle electronics sense that the vehicle has
traveled at over 18 mph (29 km/h) for about one mile
with the turn signals on, a chime will sound to alert the
driver.

Turn Signal Switch

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

147

3

«
...
145
146
147
148
149
...
»

Summary of Contents for 2006 Caravan

























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2006 Caravan

Brand: Camcar Pages: 2

Brand: Kathrein Pages: 7

Brand: Whispbar Pages: 15

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

01 29 9 416 497

Brand: BMW Pages: 5

Brand: Sirius Satellite Radio Pages: 8

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brand: Qeedon Pages: 2

ULTIMATE SPEED 296713

Brand: walser Pages: 10

Brand: Mercedes-Benz Pages: 373

Brand: Acura Pages: 6

Brand: Cadillac Pages: 335

Brand: Phonocell Pages: 8

Brand: Westin Pages: 3

Brand: Kuda Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands