Docomo FOMA P706ie, Instruction Manual, Page: 567 / 577

50
AT+COPS=n,2,m
[M]
Selects the carrier to be
connected. n=0: Automatic (searches the network and switches the
network operator automatically) (default)
n=1: Manual (connects to the network operator
specified in “m”)
n=2: Disconnects the connection to the network
operator
n=3: Mapping is not performed.
n=4: Manual/Automatic (if the connection to the network
operator specified in “m” fails, works as automatic
mode.)
m: Country code (MCC) and operator code (MNC) are
displayed in a hexadecimal number.
The format is as follows:
Digit 1 of MCC ・・・ octet 1 bits 1 to 4.
Digit 2 of MCC
・・・
octet 1 bits 5 to 8.
Digit 3 of MCC ・・・ octet 2 bits 1 to 4.
Digit 3 of MNC ・・・ octet 2 bits 5 to 8.
Digit 2 of MNC ・・・ octet 3 bits 5 to 8.
Digit 1 of MNC
・・・
octet 3 bits 1 to 4.
AT+COPS=1,2,"44F001"
OK
AT+CPAS
[M]
Displays whether to send the
control signals to the FOMA
phone. Result: +CPAS:n
n=0: Can send/receive control signals to/from the
FOMA phone.
n=1: Cannot send/receive control signals to/from the
FOMA phone.
n=2: Unknown (control signal sending/receiving is not
assured).
n=3: Can send/receive control signals to/from the
FOMA phone, and currently receiving.
n=4: Can send/receive control signals to/from the
FOMA phone, and currently communicating.
AT+CPAS
+CPAS:0
OK
AT+CPIN=n,m
[M][AT]
Enters the UIM password (PIN1
or PIN2). When the UIM is in a state waiting for the entry of PIN1
or PIN2 code
n: PIN1/PIN2
When the UIM is in a state waiting for the entry of PUK
due to failure in unblocking PIN1 or PIN2 code
n: PUK
m: New PIN1 or PIN2
AT+CPIN?: Displays the state of code entry requested
about current SIM.
Result: +CPIN: <state>
<state>=READY: Code entry not requested
<state>=SIM PIN: PIN1 code entry waited
<state>=SIM PIN2: PIN2 code entry waited
<state>=SIM PUK: PUK entry waited due to failure in
unblocking PIN1 code
<state>=SIM PUK2: PUK entry waited due to failure in
unblocking PIN2 code
AT+CPIN="1234"
OK
AT+CPIN="12345678","1234"
OK
AT+CPIN?
+CPIN:SIM PIN
OK
AT+CR=n
[M]
[&F][&W]
Displays the bearer service type
before the CONNECT result
code appears at connection of
the line. n=0: Does not display. (default)
n=1: Displays.
<serv>: Displays only “GPRS” that means packet
communication.
(Displays “SYNC”, “AV32K”, or “AV64K”,
depending on the line type.)
AT+CR?: Displays the current set value.
AT+CR=1
OK
ATD
¢
99
¢¢¢
1#
+CR: GPRS
CONNECT
AT+CRC=n
[AT][M]
[&F][&W]
Sets whether the extended result
code is used at reception. n=0: Does not use +CRING. (default)
n=1: Uses +CRING.<type>.
AT+CRC?: Displays the current setting.
The +CRING format is as follows:
+CRING: <type>
During PPP packet ringing
+CRING: GPRS “PPP”,,,<APN> AT+CRC=0
OK
AT+CRC?
+CRC: 0
OK
AT command Outline Parameter/Explanation
Command execution
example