Docomo F-08A, Manual

Page: 450 / 462

29
ATS4=<n> Set the line feed (LF) character. When result code is displayed as alphabetic characters,
appends the character after the carriage return (CR) character.
n=10 (fixed value)
ATS4? : Display current settings
ATS4=10
OK
ATS5=<n> Set the back space (BS) character. When this character is detected during command input,
the last character in the input buffer is deleted.
n=8 (fixed value)
ATS5? : Display current settings
ATS5=8
OK
ATS6=<n> Set pause time (seconds) until dialing commences but do not operate.
n= : 2-10 (default : n=5)
ATS6? : Display current settings
ATS6=5
OK
ATS8=<n> Set pause time (seconds) until commas are dialed but do not operate.
n=0-255 (default : n=3)
ATS8? : Display current settings
ATS8=3
OK
ATS10=<n>
*1
Set the delay time (1/10 seconds) for automatic disconnection but do not operate.
n=1-255 (default : n=1)
ATS10? : Display current settings
ATS10=1
OK
ATS30=<n> Set a period of time (minutes) with no data transmission/reception to terminate the
connection for 64K data communications.
n=0-255 : (default : n=0, n=0 indicates that inactive timer is set to OFF.)
ATS30? : Display current settings
ATS30=0
OK
ATS103=<n> Set the separator used to append and send received sub addresses in 64K data
communication.
n=0 :
＊ n=1 : / (default) n=2 : ￥ or \
ATS103? : Display current settings
ATS103=1
OK
ATS104=<n> Set the separator used to append and send outgoing sub addresses in 64K data
communication.
n=0 : #
n=1 : % (default) n=2 : &
ATS104? : Display current settings
ATS104=1
OK
ATV<n>
*1
Set result code display method.
n=0 : Number display
n=1 : Alphabetical display (default)
When ATV0 is executed, "0" is not returned to the same line.
ATV1
OK
ATX<n>
*1
Set whether to detect busy or dial tones and whether to display the speed in the
"CONNECT" display for the connection.
Busy tone detection : Send "BUSY" response when dialup connection is busy.
Dial tone detection : Detect whether FOMA terminal is connected.
n=0 : No busy tone, no dial tone detected, and no speed is displayed
n=1 : No busy tone, no dial tone detected, and speed is displayed
n=2 : No busy tone, dial tone detected, and speed is displayed
n=3 : Busy tone detected, no dial tone detected, and speed is displayed
n=4 : Busy tone detected, dial tone detected, and speed is displayed (default)
When n=0 is set, AT&E and AT ￥ V command will be unavailable.
ATX4
OK
ATZ
*3
Reset the current setting to the registered state.
When this command is executed during communication, the terminal is reset after the line
is disconnected (displaying "NO CARRIER").
ATZ
OK (When in offline mode)
AT%V Display FOMA terminal version.
AT%V
Ver1.00
OK
AT&C<n>
*1
Set the operating conditions of the circuit CD (DCD) for DTE.
n=0 : Always ON
n=1 : Vary according to line connection status (default)
When set to n=0, the CD signal is set to ON directly before sending "CONNECT" when
ending connection. The CD signal is set to OFF directly before the line is disconnected and
"NO CARRIER" is sent.
AT&C1
OK
Upper slot : Command
Lower slot : Example
Description