DMP Electronics 7800 Series Installation And Programming Manual Download

Page: 57 / 60

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause
undesired operation.

Changes or modifications made by the user and not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Note

: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for 7800 Series





























































Search results

Summary of Contents for 7800 Series

Reviews:

Related manuals for 7800 Series

Brands by name

Popular brands

DMP Electronics 7800 Series, Installation And Programming Manual

Search results

Summary of Contents for 7800 Series

Reviews:

Related manuals for 7800 Series

Brands by name

Popular brands